Home > IP SLA Questions

IP SLA Questions

July 11th, 2017 in ROUTE 300-101 Go to comments

Question 1

Question 2


IP SLA PBR (Policy-Based Routing) Object Tracking allows you to make sure that the next hop is reachable before that route is used. If the next hop is not reachable, another route is used as defined in the PBR configuration. If no other route is present in the route map, the routing table is used.

An example of configuring PBR based on tracking object is shown below:

//Configure and schedule IP SLA operations
ip sla 1
ip sla schedule 1 life forever start-time now
// Configure Object Tracking to track the operations
track 1 ip sla 1 reachability
//Configure ACL
ip access-list standard ACL
permit ip
//Configure PBR policing on the router
route-map PBR
match ip address ACL
set ip next-hop verify-availability track 1
set ip next-hop verify-availability track 2 -> Track 2 is not shown here but it is used if track 1 fails
//Apply PBR policy on the incoming interface of the router.
interface ethernet 0/0
ip address
ip policy route-map PBR

Reference: http://www.cisco.com/c/en/us/td/docs/switches/datacenter/sw/6_x/nx-os/IPSLA/configuration/guide/b_Cisco_Nexus_7000_Series_NX-OS_IP_SLAs_Configuration_Guide_rel_6-x/b_Cisco_Nexus_7000_Series_NX-OS_IP_SLAs_Configuration_Guide_rel_6-x_chapter_01000.html

Question 3


The keyword “tcp-connect” enables the responder for TCP connect operations. TCP is a connection-oriented transport layer protocol -> C is correct.

Question 4


The “num-packets” specifies the number of packets to be sent for a jitter operation.

The “frequency” is the rate (in seconds) at which this IP SLA operation repeats. The “tos” defines a type of service (ToS) byte in the IP header of this IP SLA operation.

Question 5


When enabled, the IP SLAs Responder allows the target device to take two time stamps both when the packet arrives on the interface at interrupt level and again just as it is leaving, eliminating the processing time. At times of high network activity, an ICMP ping test often shows a long and inaccurate response time, while an IP SLAs test shows an accurate response time due to the time stamping on the responder.

An additional benefit of the two time stamps at the target device is the ability to track one-way delay, jitter, and directional packet loss. Because much network behavior is asynchronous, it is critical to have these statistics. However, to capture one-way delay measurements the configuration of both the source device and target device with Network Time Protocol (NTP) is required. Both the source and target need to be synchronized to the same clock source. One-way jitter measurements do not require clock synchronization.

Reference: http://www.cisco.com/c/en/us/td/docs/ios-xml/ios/ipsla/configuration/15-mt/sla-15-mt-book/sla_overview.html

Question 6

Question 7

Question 8


Depending on the specific Cisco IOS IP SLAs operation, statistics of delay, packet loss, jitter, packet sequence, connectivity, path, server response time, and download time are monitored within the Cisco device and stored in both CLI and SNMP MIBs.

Reference: http://www.cisco.com/c/en/us/td/docs/ios/12_4/ip_sla/configuration/guide/hsla_c/hsoverv.html

Question 9


IP SLAs supports proactive threshold monitoring and notifications for performance parameters such as average jitter, unidirectional latency, bidirectional round-trip time (RTT), and connectivity for most IP SLAs operations. The proactive monitoring capability also provides options for configuring reaction thresholds for important VoIP related parameters including unidirectional jitter, unidirectional packet loss, and unidirectional VoIP voice quality scoring.

IP SLAs reactions are configured to trigger when a monitored value exceeds or falls below a specified level or when a monitored event, such as a timeout or connection loss, occurs. If IP SLAs measures too high or too low of any configured reaction, IP SLAs can generate a notification (in the form of SNMP trap) to a network management application or trigger another IP SLA operation to gather more data.

Cisco IOS IP SLAs can send SNMP traps that are triggered by events such as the following:
+ Connection loss
+ Timeout
+ Round-trip time threshold
+ Average jitter threshold
+ One-way packet loss
+ One-way jitter
+ One-way mean opinion score (MOS)
+ One-way latency

Question 10


Round-trip time (RTT), also called round-trip delay, is the time required for a packet to travel from a specific source to a specific destination and back again.

An ICMP Path Echo operation measures end-to-end (full path) and hop-by-hop response time (round-trip delay) between a Cisco router and devices using IP. ICMP Path Echo is useful for determining network availability and for troubleshooting network connectivity issues.

Note: ICMP Echo only measures round-trip delay for the full path.

Reference: http://www.cisco.com/c/en/us/td/docs/ios-xml/ios/ipsla/configuration/xe-3s/sla-xe-3s-book/sla_icmp_pathecho.html

Question 11


The default route command (at the last line) must include the “track” keyword for the tracking feature to work.

ip route track 10

Question 12

  1. Nei
    May 28th, 2016

    Passed 9xx

    Thanks digitaltut

  2. Nei
    May 28th, 2016

    Hello all,

    If you are looking for premium dumps, send an email @ premiumdumps@zoho(dot)com whit the exam code.


  3. Help
    September 8th, 2016

    hi everyone please help me with study material

  4. worood naif
    October 1st, 2016

    thnx :)

  5. Heads Up
    October 4th, 2016

    Guys, I failed today with a 640. The ‘300-101: Implementing Cisco IP Routing’ exam is completely different then what is on this site. Not even close. There are maybe 10 questions that are the same… What happened???

  6. please help
    October 6th, 2016

    this site is not valid any more????????

  7. lala-land
    November 3rd, 2016

    The labs are the questions are not

  8. Olivia
    December 13th, 2016

    I passed my CCDP Cisco Certified Design Professional 300-101 exam in the first attempt with the help of Grades4sure. Doing study along with job really tuff thing. I discussed my problem with my friend. He introduced me Grades4sure. I prepare my exam by Grades4sure CCDP Cisco Certified Design Professional 300-101 Braindumps and passed my exam in the first attempt. I recommended http://www.grades4sure.com/300-101-exam-questions.html to achieve the success in the first attempt.

  9. Anonymous
    December 13th, 2016

    please send the dump –
    teds2sscamaro at gmail dot com

  10. Anonymous
    January 15th, 2017

    Please send dumps to telgin1980 -at- gmail – dot – com

  11. Anonymous
    February 1st, 2017

    Is the 183q worth looking at, or stick to TAGWA and 149q????

  12. sanler
    February 3rd, 2017

    If you just want to Highest score the exam go buy a practice test from a site like https://www.examsbuzz.com/300-101-exam.html. I’m sure it will be success to everyone

  13. Anonymous
    February 5th, 2017

    Not getting question 1. Both VRRP and HSRP can also automatically detect a WAN primary link failure and failover to the secondary link (by using a track statement). Why is the answer IP SLA?

  14. CCNP Route Exam prep – what is the status on the updates?
    February 9th, 2017

    CCNP Route Exam prep – what is the status on the updates?

  15. MMMM
    February 11th, 2017

    Which to reason for IP SLA tracking failure are likely true (Choose 2)
    The threshold value is wronga. A
    route back to the R1 LAN network is missing in R2b.
    The source-interface is configures correctlyc.
    The destination must be for icmp-echod.

  16. Almond
    April 1st, 2017

    ***HELP PLEASE**Please send me latest dumps. I’ll be taking the exam this week. I promise to give back when I passed. I promise to share it. Just help me for now. For those who just recently took the exam please help us. Thanks

    Send here the dumps and some advices:

  17. bbbb
    May 14th, 2017

    Please send me latest dumps. I’ll be taking the exam this week. I promise to give back when I passed. I promise to share it. Just help me for now. For those who just recently took the exam please help us. Thanks
    Send here the dumps and some advices:
    nsfive at mail dot ru

  18. RishiRich
    May 19th, 2017

    I came across 7-8 new questions. “sh ip routing VRF” was one of them, I think someone has posted it here before.

    -In OSFP Evaluation Q:Which of the following statements is true about the serial links that terminate in R3?
    A. The R1-R3 link needs the neighbor command for the adjacency to stay up
    B. The R2-R3 link OSPF timer values are 30, 120, 120
    C. The R1-R3 link OSPF timer values should be 10,40,40
    D. R3 is responsible for flooding LSUs to all the routers on the network.

    Correct Answer was C if you check “sh ip ospf interfaces” command

    what does show ip route VRF CISCO provide?
    A. Routing table of VRF CISCO
    B. Global routing table
    C. Directly connected routes of CISCO VRF
    D. All routing table starting with CISCO
    Answer: A

    IP SLA Question was like : Why default route is not removed or something like that:

    A. The source-interface is configured incorrectly.
    B. The destination must be for icmp-echo.
    C. A route back to the R1 LAN network is missing in R2.
    D. The default route has wrong next hop IP address.

    How to set up IP SLA to monitor Bandwidth between the certain limits

    A. Timer
    B. Frequency
    C. Threshold
    D. Queue-limit – I’m not sure

    I’ve chose threshold

  19. Aerin
    May 30th, 2017

    Passed last week, 851. Sims are valid, but several questions are completely new and not on this site. Lots of VPN, redistribution and IP SLA. No questions on BGP at all. Not even one.

  20. Anonymous
    June 30th, 2017

    can u guys please send me the latest dumps on miguelfilipe_20_01 @ hotmail . com

  21. olu_ideal@yahoo.com
    July 12th, 2017

    Please guys, I need 300-101 dumps

  22. olu_ideal@yahoo.com
    July 12th, 2017

    i need current dumps
    olu_ideal at yahoo dot com

  23. science
    July 14th, 2017

    I need current dumps please
    arnaud.teug at gmail dot com

  24. Anonymous
    July 18th, 2017

    I have the latest 300-101 dump 423q. update July 13.. let me know – iastate80 at yahoo dot com

  25. farid
    July 19th, 2017

    Hi Anonymous,

    I have sent you mail regarding new dump 423q to your mentioned mail(iastate80 at yahoo dot com). Waiting response from your side.


  26. not_my_real_name
    July 23rd, 2017

    can someon send the latest dumps to LCEICH(@)GMAIL(dot)COM

  27. dapo
    August 23rd, 2017

    Hi there,

    How come there is no question title or description?


  28. Anonymous
    August 27th, 2017

    Question 12 is not very clear. As according to the Cisco’s own reference, the answer could also be IP-route tracking.

  29. Steffy
    August 28th, 2017

    Hello friends, for latest valid dump with continuous update, please contact me at steffyshirls @ gmail .com

  30. kuishman
    September 12th, 2017

    can u guys please send me the latest dumps on makuish @ hotmail .com

  31. kuishman
    September 12th, 2017

    or marco . hq90 @ gmail . com

  32. cl
    September 29th, 2017
  33. msantanaribeiro
    October 2nd, 2017

    Hello friends, for latest valid dump with continuous update, please contact me at m.santanaribeiro @ gmail . com

  34. Peter Pan
    October 7th, 2017

    Q6 – answer A or B ?

    B seems the better answer.

  35. learner
    October 13th, 2017

    Q 11:
    D. missing of track feature on default static route command – correct

    IP SLA Tracking with Configuration Example


    <ip sla 1

    timeout 500
    frequency 3

    ip sla schedule 1 start-time now life forever

    track 1 rtr 1 reachability

    now for the routing, we need to change the default route and associate it with the tracker

    no ip route

    and then put it back with the tracking

    ip route track 1


  36. Colin
    October 31st, 2017

    Thanks all, done with the router. 440q dumps from IT-Libraries are valid. Practice the labs since the ips change on the exam

  37. Shawn
    November 9th, 2017

    Smashed my route exam today, 9xx used the dumps from it libraries and tut.

  38. durshen
    November 11th, 2017

    Hello everyone, I have the valid dump with me and I’m wiling to share. Please contact me via durshen81 @ gmail .com

  39. durshen
    November 11th, 2017

    Hello buddies, I have the valid dump with me and I’m wiling to share. Please contact me via durshen81 @ gmail .com

  40. Elmo
    November 14th, 2017

    You can find the it-libraries dumps here https://drive.google.com/open?id=0B5mAFqgydmCzNno3dnFocF9HckU

  41. Alphonse
    November 21st, 2017

    Smashed my route exam today, 9xx used the dumps from it libraries and tut.

  42. Cyrus
    November 28th, 2017

    Confirming the 440q dumps are valid.

  43. Paris
    November 28th, 2017

    Dose anyone have the full version for this dumps? https://drive.google.com/open?id=0B5mAFqgydmCzQUh0SUxOdE03VGc

  44. Nick
    November 29th, 2017

    DO NOT USE http://www.myexamcollection.com/ ITS A FAKE

  45. Bret
    December 4th, 2017

    Passed, if you go the exam study the 21q dumps.

  46. Shawn
    December 5th, 2017

    Passed today, used the 440q dumps. you can find them on https://drive.google.com/open?id=0B5mAFqgydmCzd1duSE5uLVhkVFk

  1. No trackbacks yet.